usbsksp(7D) Devices usbsksp(7D)NAMEusbsksp - Keyspan USB to serial converter driver
SYNOPSIS
#include <fcntl.h>
#include <sys/termio.h>
usbskpsp@unit
DESCRIPTION
The usbsksp driver is a loadable STREAMS and USBA (Solaris USB archi‐
tecture) compliant client driver that provides basic asynchronous com‐
munication support for Keyspan USB-to-serial converters. The usbsksp
driver supports the Keyspan USA19HS, USA49WG and USA49WLC models. By
default, the USA19HS and USA49WG models are compatible with the usbsksp
driver and no configuration or installation steps are required. (The
USA49WG model is a USB 2.0 device comforming to Universal Serial Bus
Specification 2.0 and the USB 2.0 host controller is required to sup‐
port the USA49WG model. Note that the USA49WG is not compatible with
USB 1.1 host controllers). If you use the Keyspan USA49WLC model, you
must download and install a firmware package to enable the device to
work with the usbsksp driver. See the Keyspan website
(http://www.keyspan.com/downloads/sun/) for more information. Serial
device streams are built with appropriate modules that are pushed
atop the usbsksp driver by the autopush(1M) facility.
The usbsksp module supports the termio(7I) device control functions
specified by flags in the c_cflag word of the termios structure, and by
the IGNBRK, IGNPAR, PARMRK and INPCK flags in the c_iflag word of the
termios structure. All other termio(7I) functions must be performed by
STREAMS modules pushed atop the driver. When a device is opened, the
ldterm(7M) and ttcompat(7M) STREAMS modules are automatically pushed
on top of the stream, providing the standard termio(7I) interface.
Use device logical names /dev/term/[0-9]* to access the serial
ports. These names are typically used to provide a logical access point
for a dial-in line that is used with a modem.
A special feature (controlled by the minor device number) is available
that enables a single tty line to be connected to a modem and used for
incoming and outgoing calls. By accessing through device logical name
/dev/cua/[0-9]*, you can open a port without the carrier detect signal
being asserted, either through hardware or an equivalent software mech‐
anism. These devices are commonly known as 'dial-out' lines.
Unlike onboard serial ports, the usbsksp ports cannot serve as a local
serial console.
APPLICATION PROGRAMMING INTERFACE
A dial-in line can be opened only if the corresponding dial-out line is
closed. A blocking /dev/term open waits until the /dev/cua line is
closed (which drops Data Terminal Ready, after which Carrier Detect
usually drops as well) and carrier is detected again. A non-blocking
/dev/term open returns an error if the /dev/cua is open.
If the /dev/term line is opened successfully (usually only when car‐
rier is recognized on the modem), the corresponding /dev/cua line can‐
not be opened. This allows a modem and port to be used for dial-in (by
enabling the line for login in /etc/inittab) or dial-out (by tip(1), or
uucp(1C)) when no one is logged in on the line.
Device hot-removal is functionally equivalent to a modem disconnect
event, as defined in termio(7I).
IOCTLS
The usbsksp driver supports the standard set of termio(7I) ioctl
calls.
Input and output line speeds can be set to the following baud rates:
0, 50, 75, 110, 134, 150, 200, 300, 600, 1200, 1800, 2400, 4800, 9600,
19200, 38400, 57600, 115200, or 230400. Input and output line
speeds cannot be set independently. For example, when the output speed
is set, the input speed is automatically set to the same speed.
ERRORS
An open() fails under the following conditions:
ENXIO The unit being opened does not exist.
EBUSY The /dev/cua (dial-out) device is being opened while the
/dev/term (dial-in device) is open, or the dial-in device is
being opened with a no-delay open while the dial-out device is
open.
EBUSY The unit has been marked as exclusive-use by another process
with a TIOCEXCL ioctl() call.
EIO USB device I/O error.
FILES
/kernel/drv/usbsksp
32-bit x86 ELF kernel module.
/kernel/drv/amd64/usbsksp
64-bit x86 ELF kernel module.
/kernel/drv/sparcv9/usbsksp
64-bit SPARC ELF kernel module.
/dev/cua/[0-9]*
dial-out tty lines.
/dev/term/[0-9]*
dial-in tty lines.
ATTRIBUTES
See attributes(5) for descriptions of the following attributes:
┌─────────────────────────────┬──────────────────────────────┐
│ ATTRIBUTE TYPE │ ATTRIBUTE VALUE │
├─────────────────────────────┼──────────────────────────────┤
│Architecture │SPARC, x86, PCI-based systems │
├─────────────────────────────┼──────────────────────────────┤
│Availability │SUNWuksp │
└─────────────────────────────┴──────────────────────────────┘
SEE ALSOstrconf(1), tip(1), uucp(1C), autopush(1M), ioctl(2), open(2),
termios(3C), attributes(5), usba(7D), termio(7I), ldterm(7M), ttcom‐
pat(7M)DIAGNOSTICS
In addition to being logged, the following messages may appear on the
system console. All messages are formatted in the following manner:
Warning: <device path> (usbsksp<instance num>): Error Message...
Device was disconnected while open. Data may have been lost.
The device has been hot-removed or powered off while it was open
and a possible data transfer was in progress. The job may be
aborted.
Device is not identical to the previous one on this port. Please dis‐
connect and reconnect.
The device was hot-removed while open. A new device was hot-
inserted which is not identical to the original device. Please dis‐
connect the device and reconnect the original device to the same
port.
Device has been reconnected, but data may have been lost.
The device that was hot-removed from its USB port has been re-
inserted again to the same port. It is available for access but
data from a previous transfer may be lost.
Cannot access <device>. Please reconnect.
This device has been disconnected because a device other than the
original one has been inserted. The driver informs you of this fact
by displaying the name of the original device.
No valid firmware available for Keyspan usa49wlc usb-to-serial adapter.
Please download it from Keyspan website and install it.
By default, only an empty firmware package is installed for the
usa49wlc model. Please download the SUNWukspfw package from
Keyspan's web site and install it.
The following messages may be logged into the system log. They are for‐
matted in the following manner:
<device path><usbsksp<instance number>): message...
Input overrun Data was lost.
SunOS 5.10 114 Oct 2007 usbsksp(7D)