mount.ocfs2 man page on OpenSuSE
[printable version]
mount.ocfs2(8) OCFS2 Manual Pages mount.ocfs2(8)
NAME
mount.ocfs2 - mount an OCFS2 filesystem
SYNOPSIS
mount.ocfs2 [-vn] [-o options] device dir
DESCRIPTION
mount.ocfs2 mounts an OCFS2 filesystem at dir. It is usually invoked
indirectly by the mount(8) command.
OPTIONS
_netdev
Indicates that the file system resides on a device that requires
network access (used to prevent the system from attempting to
mount these filesystems until the network has been enabled on
the system). mount.ocfs2(8) transparently appends this option
during mount. However, users mounting the volume via /etc/fstab
must explicitly specify this mount option to delay the system
from mounting the volume until after the network has been
enabled.
noatime
The file system will not update access time.
relatime
The file system will update atime only if the on-disk atime is
older than mtime or ctime.
strictatime,atime_quantum=nrsec
The file system will always perform atime updates, but the mini‐
mum update interval is specified by atime_quantum which defaults
to 60 secs. Set it to zero to always update atime. These two
options need work together.
[no]acl
Enables / disables POSIX ACLs (access control lists) support.
[no]user_xattr
Enables / disables extended user attributes.
commit=nrsec
Sync all data and metadata every nrsec seconds. The default
value is 5 seconds. Zero means default.
data=[ordered|writeback]
Specifies the handling of file data during metadata journalling.
ordered
This is the default mode. Data is flushed to disk before
the corresponding meta-data is committed to the journal.
writeback
Data ordering is not preserved - data may be flushed to
disk after the corresponding meta-data is committed to
the journal. This is rumored to be the higher-throughput
option. While it guarantees internal file system
integrity, it can allow old data to appear in files after
a crash and journal recovery.
errors=[remount-ro|errors=panic]
Specifies the behavior when an on-disk corruption is encoun‐
tered.
remount-ro
This is the default mode. The file system is remounted
read-only.
panic The system is halted via panic.
localflocks
This disables cluster-aware flock(2).
coherency=[full|coherency]
Specifies the extent of coherency for the cached file data
across the cluster. This mount option works with Linux kernel
2.6.37 and later.
full This is the default mode. The file system ensures the
cached file data is coherent across the cluster for all
IO modes.
buffered
The file system only ensures the cached file data
coherency for buffered mode IOs. It does not perform IO
serialization for direct IOs. This allows multiple nodes
to perform concurrent direct IOs to the same file. This
is the recommended mode for volumes hosting database
files.
resv_level=level
Specifies the level of allocation reservation for files. The
higher the value, the more aggressive it is. Valid values are
between 0 (reservation off) to 8 (maximum space for reserva‐
tion). It defaults to 2. This mount option works with Linux ker‐
nel 2.6.35 and later.
dir_resv_level=level
By default, directory reservation scales with file reservera‐
tion. Users should rarely need to change this value. If the file
allocation reservation is turned off, this option will have no
effect. This mount option works with Linux kernel 2.6.35 and
later.
inode64
Indicates that the file system can create inodes at any location
in the volume, including those which will result in inode num‐
bers greater than 4 billion.
[no]intr
Specifies whether a signal can interrupt IOs. It is disabled by
default.
ro Mount the file system read-only.
rw Mount the file system read-write.
NOTES
To mount and umount a OCFS2 volume, do:
# mount /dev/sda1 /mount/path
...
# umount /mount/path
Users mounting a clustered volume should be aware of the following:
1. The cluster stack must to be online for a clustered mount to
succeed.
2. The clustered mount operation is not instantaneous; it must wait
for the node to join the DLM domain.
3. Likewise, clustered umount is also not instantaneous; it
involves migrating all mastered lock-resources to the other nodes
in the cluster.
If the mount fails, detailed errors can be found via dmesg(8). These
might include incorrect cluster configuration (say, a missing node or
incorrect IP address) or a firewall interfering with o2cb network traf‐
fic. Check the configuration as listed in o2cb(7) or the man page of
the active cluster stack.
To auto-mount volumes on startup, the file system tools include an
ocfs2 init service. This runs after the o2cb init service has started
the cluster. The ocfs2 init service mounts all OCFS2 volumes listed in
/etc/fstab.
# chkconfig --add o2cb
o2cb 0:off 1:off 2:on 3:on 4:off 5:on 6:off
$ chkconfig --add ocfs2
o2cb 0:off 1:off 2:on 3:on 4:off 5:on 6:off
$ cat /etc/fstab
...
/dev/sda1 /u01 ocfs2 _netdev,defaults 0 0
...
SEE ALSO
debugfs.ocfs2(8) fsck.ocfs2(8) mkfs.ocfs2(8) mounted.ocfs2(8) o2cb(7)
o2cluster(8) o2image(8) o2info(1) tunefs.ocfs2(8)
AUTHORS
Oracle Corporation
COPYRIGHT
Copyright © 2004, 2012 Oracle. All rights reserved.
Version 1.8.2 January 2012 mount.ocfs2(8)
[top]
List of man pages available for OpenSuSE
Copyright (c) for man pages and the logo by the respective OS vendor.
For those who want to learn more, the polarhome community provides shell access and support.
[legal]
[privacy]
[GNU]
[policy]
[cookies]
[netiquette]
[sponsors]
[FAQ]
Polarhome, production since 1999.
Member of Polarhome portal.
Based on Fawad Halim's script.
....................................................................
|
Vote for polarhome
|