ndmpstat(1M) System Administration Commands ndmpstat(1M)NAMEndmpstat - show NDMP backup progress statistics
SYNOPSISndmpstat [tapes] [interval [count]]
DESCRIPTION
The ndmpstat utility reports Network Data Management Protocol (NDMP)
statistics, among which are NDMP worker threads, disk IO, tape IO,
files operation, performance, and backup activity.
ndmpstat reports the aggregate statistics for all tapes and disks. In
order to obtain statistics for specific tape devices, the tape device
name should be passed as argument to the utility.
When invoked, ndmpstat begins its display with a one-line summary of
the NDMP daemon activity since the NDMP service was invoked.
Display Fields
The fields in ndmpstat output are described as follows:
wthr
Report the number of worker threads in each of the four following
states:
r
the number of worker threads running
w
the number of blocked worker threads that are waiting for
resources such as I/O and paging
b
the number of backup operations currently running
r
the number of restore operations currently running
file
Report on usage of filesystem.
rd
the number of files being read
wr
the number of files being written
disk
Report the number of disk operations per interval.
rd
the number of disk blocks being read
wr
the number of disk blocks being written
tape
Report the number of tape operations per interval. There are slots
for up to four tapes, labeled with a single number. The number
indicates the name of the device under /dev/rmt.
rd
the number of tape blocks being read
wr
the number of tape blocks being written
bytes
Report the number of bytes transferred. This is the aggregate value
of both tape and disk devices. The number is in kilobytes.
rd
the number of kilobytes being read
wr
the number of kilobytes being written
perf
Displays a rough estimate of performance of the backup/restore
operation in megabytes per second.
bk
backup performance
rs
restore performance
prcnt
Display the comparative usage of resources, in percent.
dsk
disk I/O time
tpe
tape I/O time
otr
other time (memory or idle)
See EXAMPLES.
OPERANDS
The following operands are supported:
count Specifies the number of times that the statistics display
is repeated.
tape Specifies which tapes are to be given priority in the out‐
put. A command line is limited to a maximum of four tape
devices. A common tape name is /dev/rmt/n, where n is an
integer.
interval Specifies the number of seconds over which ndmpstat summa‐
rizes activity. The specified interval remains in effect
till the command is terminated.
EXAMPLES
Example 1 Using ndmpstat
The following command displays a summary of NDMP daemon activity at
five-second intervals.
example% ndmpstat 5
wthr file disk tape bytes perf prcnt
r w b r rd wr rd wr rd wr rd wr bk rs dsk tpe otr
1 0 3 6 50 9 1250 0 32544 4455 42335 3234 5 4 20 40 40
1 0 0 1 1 0 128 0 0 128 64 64 1 0 0 80 20
1 0 0 1 2 0 128 0 0 0 64 0 1 0 80 0 20
1 0 0 1 1 0 128 0 0 0 64 0 1 0 80 0 20
1 0 0 1 3 0 128 0 0 0 64 0 0 0 80 0 20
1 0 0 1 1 0 128 0 0 128 64 64 1 0 0 80 20
^C
example%
ATTRIBUTES
See attributes(5) for descriptions of the following attributes:
┌─────────────────────────────┬─────────────────────────────┐
│ ATTRIBUTE TYPE │ ATTRIBUTE VALUE │
├─────────────────────────────┼─────────────────────────────┤
│Availability │service/storage/ndmp │
├─────────────────────────────┼─────────────────────────────┤
│Interface Stability │See below │
└─────────────────────────────┴─────────────────────────────┘
Invocation is evolving. Human readable output is unstable.
SEE ALSOiostat(1M), mpstat(1M), ndmpd(1M), ndmpadm(1M), attributes(5)NOTES
Performance numbers are not accurate and are rounded up at the MB/sec.
boundary.
SunOS 5.11 21 Jun 2007 ndmpstat(1M)