FSDB(8) BSD System Manager's Manual FSDB(8)NAMEfsdb - FFS debugging/editing tool
SYNOPSISfsdb [-d] -f fsname
DESCRIPTIONfsdb opens fsname (usually a raw disk partition) and runs a command loop
allowing manipulation of the file system's inode data. You are prompted
to enter a command with fsdb (inum X)> where X is the currently selected
i-number. The initial selected inode is the root of the file system (i-
number 2).
The command processor uses the editline(3) library, so you can use com-
mand line editing to reduce typing if desired. When you exit the command
loop, the file system superblock is marked dirty and any buffered blocks
are written to the file system.
The options are as follows:
-d Enables additional debugging output (which comes primarily from
fsck(8)-derived code).
Besides the built-in editline(3) commands, fsdb supports these commands:
help Print out the list of accepted commands.
inode i-number
Select inode i-number as the new current inode.
back Revert to the previously current inode.
clri i-number
Clear the inode i-number.
lookup name, cd name
Find name in the current directory and make its inode the current
inode. Name may be a multi-component name or may begin with slash
to indicate that the root inode should be used to start the look-
up. If some component along the pathname is not found, the last
valid directory encountered is left as the active inode.
This command is valid only if the starting inode is a directory.
active, print
Print out the active inode.
uplink Increment the active inode's link count.
downlink
Decrement the active inode's link count.
linkcount number
Set the active inode's link count to number.
ls List the current inode's directory entries. This command is valid
only if the current inode is a directory.
rm name, del name
Remove the entry name from the current directory inode. This com-
mand is valid only if the current inode is a directory.
ln ino name
Create a link to inode ino under the name name in the current
directory inode. This command is valid only if the current inode
is a directory.
chinum dirslot inum
Change the i-number in directory entry dirslot to inum.
chname dirslot name
Change the name in directory entry dirslot to name. This command
cannot expand a directory entry. You can only rename an entry if
the name will fit into the existing directory slot.
chtype type
Change the type of the current inode to type. type may be one of:
file, dir, socket, or fifo.
chmod mode
Change the mode bits of the current inode to mode. You cannot
change the file type with this subcommand; use chtype to do that.
chflags flags
Change the file flags of the current inode to flags.
chown uid
Change the owner of the current inode to uid.
chlen length
Change the length of the current inode to length.
chgrp gid
Change the group of the current inode to gid.
chgen gen
Change the generation number of the current inode to gen.
mtime time, ctime time, atime time
Change the modification, change, or access time (respectively) on
the current inode to time. Time should be in the format
YYYYMMDDHHMMSS[.nsec] where nsec is an optional nanosecond
specification. If no nanoseconds are specified, the mtimensec,
ctimensec, or atimensec field will be set to zero.
quit, q, exit, <EOF>
Exit the program.
SEE ALSOeditline(3), fs(5), clri(8), fsck(8)HISTORYfsdb uses the source code for fsck(8) to implement most of the file sys-
tem manipulation code. The remainder of fsdb first appeared in
NetBSD 1.1.
BUGS
Manipulation of "short" symlinks doesn't work (in particular, don't try
changing a symlink's type).
You must specify modes as numbers rather than symbolic names.
There are a bunch of other things that you might want to do which fsdb
doesn't implement.
WARNING
Use this tool with extreme caution you can damage an FFS file system
beyond what fsck(8) can repair.
MirOS BSD #10-current September 14, 1995 1