AHCI(4) BSD Kernel Interfaces Manual AHCI(4)NAMEahci — Serial ATA Advanced Host Controller Interface driver
SYNOPSIS
To compile this driver into the kernel, place the following lines in your
kernel configuration file:
device pci
device scbus
device ahci
Alternatively, to load the driver as a module at boot time, place the
following line in loader.conf(5):
ahci_load="YES"
The following tunables are settable from the loader(8):
hint.ahci.X.msi
controls Message Signaled Interrupts (MSI) usage by the specified con‐
troller
0 MSI disabled;
1 single MSI vector used, if supported (default);
2 multiple MSI vectors used, if supported;
hint.ahci.X.ccc
controls Command Completion Coalescing (CCC) usage by the specified con‐
troller. Non-zero value enables CCC and defines maximum time (in ms),
request can wait for interrupt, if there are some more requests present
on controller queue. CCC reduces number of context switches on systems
with many parallel requests, but it can decrease disk performance on some
workloads due to additional command latency.
hint.ahcich.X.pm_level
controls SATA interface Power Management for the specified channel,
allowing some power to be saved at the cost of additional command
latency. Possible values:
0 interface Power Management is disabled (default);
1 device is allowed to initiate PM state change, host is pas‐
sive;
2 host initiates PARTIAL PM state transition every time port
becomes idle;
3 host initiates SLUMBER PM state transition every time port
becomes idle.
4 driver initiates PARTIAL PM state transition 1ms after port
becomes idle;
5 driver initiates SLUMBER PM state transition 125ms after
port becomes idle.
Some controllers, such as ICH8, do not implement modes 2 and 3 with NCQ
used. Because of artificial entering latency, performance degradation in
modes 4 and 5 is much smaller then in modes 2 and 3.
Note that interface Power Management is not compatible with device pres‐
ence detection. A manual bus reset is needed on device hot-plug.
hint.ahcich.X.sata_rev
setting to nonzero value limits maximum SATA revision (speed). Values 1,
2 and 3 are respectively 1.5, 3 and 6Gbps.
DESCRIPTION
This driver provides the CAM(4) subsystem with native access to the SATA
ports of AHCI-compatible controllers. Each SATA port found is repre‐
sented to CAM as a separate bus with one target, or, if HBA supports Port
Multipliers, 16 targets. Most of the bus-management details are handled
by the SATA-specific transport of CAM. Connected ATA disks are handled
by the ATA protocol disk peripheral driver ada(4). ATAPI devices are
handled by the SCSI protocol peripheral drivers cd(4), da(4), sa(4), etc.
Driver features include support for Serial ATA and ATAPI devices, Port
Multipliers (including FIS-based switching, when supported), hardware
command queues (up to 32 commands per port), Native Command Queuing, SATA
interface Power Management, device hot-plug and Message Signaled Inter‐
rupts.
AHCI hardware is also supported by ataahci driver from ata(4) subsystem.
If both drivers are loaded at the same time, this one will be given
precedence as the more functional of the two.
HARDWARE
The ahci driver supports AHCI compatible controllers having PCI class 1
(mass storage), subclass 6 (SATA) and programming interface 1 (AHCI).
Also, in cooperation with atamarvell and atajmicron drivers of ata(4), it
supports AHCI part of legacy-PATA + AHCI-SATA combined controllers, such
as JMicron JMB36x and Marvell 88SX61xx.
SEE ALSOada(4), ata(4), cam(4), cd(4), da(4), sa(4)HISTORY
The ahci driver first appeared in FreeBSD 8.0.
AUTHORS
Alexander Motin ⟨mav@FreeBSD.org⟩.
BSD January 28, 2010 BSD